Teknisk support Industrielle sensorer
Kundeservice, eksplosjonsbeskyttelse
Ikke tilgjengelig for salg
Ikke tilgjengelig for salg

Signal converter K23-SSI/R2/25B-C

K23-SSI/R2/25B-C
  • Suitable for the connection of sensors and absolute rotary encoders with SSI interface
  • Converts both SSI data and serial data into a parallel format
  • Parallel output 25 bit (Push-pull, short-circuit proof)
  • RS 232 Interface for the serial read out of sensor information
  • SSI:Master or slave operation
  • Specified option for arbitrary linearization characteristics
  • Additional functions such as z. B. bit masking, concentricity function
  • Supply 18 V DC ... 30 V DC

Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.

Last ned komplett datablad som PDF:


Datablad utdrag: Tekniske data for  K23-SSI/R2/25B-C

Produktbeskrivelse
Signal converter SSI/RS 232/Parallel
Electrical specifications
Rated operating voltage18 ... 30 V DC
Rated operating current≤ 200 mA
Input 1
Input typeSSI
Input formatGray code, binary code
Resolution13, 21, or 25 bit
Input frequency100 Hz ... 1 MHz
Input 2
Input typeHTL (Hold)
Signal voltage
High≥ 10 V
Low≤ 3 V
Internal resistor5 kΩ
Output
Number/TypeParallel
Output rated operating currentGray-Code, Binary-Code, BCD-Code
Contact loadingmax. 35 V on COM+ (Short-circuit resistance up to 27 V)
max. 1.2 kA ± 10 % at 24 V (Ri = 600 Ω)
Ambient conditions
Ambient temperature0 ... 45 °C (32 ... 113 °F)
Mechanical specifications
Connectionscrew terminals , max. core cross-section 0.34 ... 2.5 mm2
Massapprox. 190 g

Classifications

SystemClasscode
ECLASS 13.027210904
ECLASS 12.027210904
ECLASS 11.027210904
ECLASS 10.0.127210904
ECLASS 9.027210904
ECLASS 8.027210904
ECLASS 5.127210904
ETIM 9.0EC002918
ETIM 8.0EC002918
ETIM 7.0EC002918
ETIM 6.0EC002918
ETIM 5.0EC002475
UNSPSC 12.139121007

Details: K23-SSI/R2/25B-C

Function

K23-SSI/R2/25B-C represents a small and low-cost, but highly performant converter for industrial applications, where the information of a sensor or encoder with SSI interface needs to be converted to a parallel signal or a serial RS 232 data format. Also it is possible to convert serial RS 232 data to a parallel format. The unit has been designed as a compact module with 12 screw terminals, a 9-pin and a 25-pin Sub-D connector (female). The housing is suitable for standard DIN rail mounting.

Applicable encoders and sensors:

Single-turn or multi-turn absolute encoders and all similar sensors using a standard SSI interface (6 .. 25 bits of resolution with binary or Gray code). The unit can operate in either master mode (clock signal generated by the unit), or in slave mode (clock signal generated by a remote device).

Remark about the encoder resolution:

The unit provides settings for the standard resolutions of 13 bits, 21 bits and 25 bits. In general, for sensors with other resolutions you can use the next higher setting (i. e. set the unit to 21 bits with a sensor of 16 bits).

Depending on brand and specification of the encoder, in some cases it may be necessary to blank out the surplus bits by using the bit blanking function described later. In general however, the unit should work perfectly also without special bit blanking.

Product Documentation: K23-SSI/R2/25B-C

Velg språk:
ManualsSpråkFiltypeFilstørrelse
Operating Instructions K23-SSI/R2/25B-CENGPDF238 KB

Software: K23-SSI/R2/25B-C

Velg språk:
Software ToolsFrigivelsesinfoFiltypeFilstørrelse
software tool to configure K23-SSI devices and TC-LCDC displays / Parametrier- und Konfigurationssoftware für K23-SSI und TC-LCDC08/2021ZIP85353 KB